Texas Well Water Quality Atlas
Is the county figure a good guide to the water in my well?
Not as good as the tested wells around you. In a Texas study whose rules and code were fixed and timestamped before it was run, estimating a well's arsenic from tested wells within 15 miles had 10.6% less error than using the county figure, and for nitrate 5.3% less. Nearby tests also beat the USGS national arsenic model by 15.4%, and knowing the aquifer added nothing once they were known. No estimate replaces testing your own well.
Data: Texas Water Development Board Groundwater Database, file of November 13, 2026; Water Quality Portal (USGS and EPA), download of November 15, 2026. Page published November 16, 2026.
The figures
- Arsenic test wells
- 8,715
- Less error than the county figure
- 10.6%
- arsenic
- Less error than the county figure
- 5.3%
- nitrate
- Less error than the USGS model
- 15.4%
- 7,904 wells
- Test wells with 10 tested wells within 15 miles
- 97%
What each source of information does to the error
Leave one well out: each test well is estimated without itself or any well within 500 m. Measure: Brier score. 95% intervals unless noted.
| Comparison | Arsenic | Nitrate |
|---|---|---|
| Nearby tested wells vs. the county figure | error 10.6% lowerfrom error 5.8% lower to error 15.5% lower | error 5.3% lowerfrom error 1.0% lower to error 10.3% lower |
| Nearby wells vs. the USGS national arsenic model | error 15.4% lowerfrom error 9.9% lower to error 20.6% lower | — |
| Adding the aquifer to nearby wells (fixed in advance, 97.5%) | error 0.7% higherfrom error 2.7% higher to error 1.3% lower | — |
| Filtering by the county's typical home-well depth (97.5%) | error 4.7% higherfrom error 7.6% higher to error 1.9% higher | error 3.8% higherfrom error 6.6% higher to error 1.5% higher |
What to do with this
- Look at the tested wells near the property, not only the county or the aquifer. The county table and each county page of the Well Atlas show what was found nearby.
- Where there are no tests nearby, the USGS national arsenic model is a better guide than nearby wells, because there are none.
- Then test the well itself: that is the only answer about one well.
What this shows and what it doesn't
- It does not predict a well that has not been drilled.
- The comparison with the USGS model is not between equals: the model estimates with no nearby test, for private wells; nearness uses the tests next door, of every use.
- It does not say the aquifer is irrelevant: once there are 10 tested wells within 15 miles, the aquifer's name does not lower the error.
Test your own well
No map or table can say what is in the water of one well. These figures say how often the tested wells of an area went over a limit; the only way to know your well is to have its water tested by an accredited laboratory.
The drinking-water standards used here apply to public water systems. No law requires a private well to meet them: here they are only the yardstick.
Sources you can check
- Texas Water Development Board, Groundwater Database. File of November 13, 2026: the core of every figure. How the state explains its database.
- Water Quality Portal (USGS and EPA), download of November 15, 2026: well sites in Texas, after removing duplicates of state records.
- USGS, national model of arsenic in private wells (data) and the article that describes it: Lombard and others, 2021, Environmental Science & Technology.
- This dataset on Zenodo: the CSV files, a README with the method, the license and checksums. DOI 10.5281/zenodo.24287393.
Check it yourself
- Download the CSV (estudio-resultados_study-results.csv): every figure on this page is a cell of the open files.
- The same files are archived on Zenodo with checksums, so you can confirm a copy is unchanged.
- If a figure does not match, write to us with the number: we correct it and say so.
How we got it
Each method gives a probability of exceeding, (K + 0.5) / (N + 1), with K wells above the limit out of N. Nearby wells are those in the first radius of 5, 10 or 15 miles that gathers 10 tested wells.
The study was run once; three independent programs gave the same probability for every test well.
The full method · All open data
How to cite this
Blanco, R. (2026). "Is the county figure a good guide to the water in my well?." Texas Well Water Quality Atlas. TerraFunded. https://terrafunded.com/water-quality/findings/county-figure-vs-nearby-wells. Data: https://doi.org/10.5281/zenodo.24287393
Free to use with credit under CC BY 4.0. Please also credit the Texas Water Development Board. Dataset DOI: 10.5281/zenodo.24287393.
More questions
How common is arsenic in Texas well water?
Among 10,379 Texas wells with arsenic tested since 1992, 742 (7.1%) exceeded the 10 µg/L drinking-water limit in their most recent test.
Where is nitrate highest in Texas wells?
Among 11,026 Texas wells with nitrate tested since 1992, 697 (6.3%) exceeded 10 mg/L as nitrogen in their most recent test.
How common is fluoride above the limit in Texas well water?
Among 10,964 Texas wells with fluoride tested since 1992, 427 (3.9%) exceeded the 4 mg/L drinking-water limit in their most recent test, and 2,078 (19.0%) were above the 2 mg/L secondary level.
How salty is Texas well water?
Nearly one in four tested Texas wells (2,434 of 10,656, 22.8%) had more than 1,000 mg/L of total dissolved solids in its most recent test since 1992.
Do private wells in Texas have more nitrate than public wells?
Yes: 8.5% of domestic wells against 1.8% of public wells; 8.3% against 4.0% comparing similar wells.
How often should I retest my Texas well water?
Near the limit, yes: 23% of wells with 8 to 10 µg/L of arsenic exceeded it later. Far from it, about 1% changed.
Which Texas counties have no well water quality data?
Archer, Rockwall, Shackelford and Stephens: no well tested for arsenic or nitrate since 1992.

Rodrigo Blanco, Founder and CEO of TerraFunded, a Texas company that sells rural land. These pages carry no listings, prices or offers.
Reviewed by two AI models in six rounds and checked with three independent programs; not yet reviewed by outside specialists.
Press and researchers: [email protected]
