Skip to content
ENES
Marketplace

How deep are water wells in Warren City, Texas?

Home water wells in and around Warren City, Texas are typically 380 to 450 feet deep (median 420 ft, 37 wells reported since 2001). Estimated cost of a complete well at the median depth: $13,000 to $31,500.

Updated every day from Texas Water Development Board driller reports. Last update: November 11, 2026, using the state file of November 10, 2026.

See the wells and layers at an exact pointGregg County
What is under Warren City, TexasUnderground column at the center of Warren City: median well 420 ft, middle half 380 to 450 ft, water at 180 ft.No state layer model here yet0200400600ftGround levelMedian well: 420 ftWater standing in the well from 180 ftWater level180 ftMiddle half380–450 ftMedian well420 ft

Under Warren City, Gregg County

The well and the water are the median of 37 real wells. This atlas does not have a state layer model for this area yet.

Home wells in and around Warren City

Each dot is a home well from a state driller report, colored by depth. Tap one for its details and official report. Tap an empty spot to see what is under that point.

See underground

Well depth (ft)

  • <100
  • 100
  • 200
  • 300
  • 400
  • 600
  • 800+

Dashed line: Warren City and about 2 miles around it

Key figures

Typical depth (middle half)
380 to 450 feet
Median depth
420 feet
Deepest 10% are past
498 feet
Water level (median)
180 feet
29 wells
Yield (median)
27 gpm
33 wells, gallons per minute
Wells used
37
Since 2001
Inside the city limits
0
the rest within 2 miles
All years on file
37
median 420 ft, since 2001
Confidence
Standard (30 or more wells)

When the wells were finished, the water stood a median 180 feet below the surface (29 wells), well above the bottom: the typical well holds about 240 feet of water.

What is under Warren City, TexasUnderground column at the center of Warren City: median well 420 ft, middle half 380 to 450 ft, water at 180 ft.No state layer model here yet0200400600ftGround levelMedian well: 420 ftWater standing in the well from 180 ftWater level180 ftMiddle half380–450 ftMedian well420 ft
The well and the water are the median of 37 real wells. This atlas does not have a state layer model for this area yet.

Which formation do wells in Warren City draw from?

We cannot say yet for Warren City. This atlas assigns layers with the TWDB layered models processed so far (the Northern Trinity and Woodbine model, the Hill Country Trinity model, the northern Gulf Coast Aquifer model and the High Plains Aquifer System model), and none covers this area with enough wells. The depth, water level and yield on this page do come from the real wells here.

See the aquifers mapped under Gregg County

Depth over time

Too few wells per period in and around Warren City to compare depth over time. Since 2001, 37 home wells have been reported, with a median of 420 feet.

PeriodMedian depth (ft)Wells
2001–200540616
2006–2010under 10 wells2
2011–2015under 10 wells6
2016–2020under 10 wells4
2021–2025under 10 wells8
2026under 10 wells1

What a well costs in Warren City

At the median depth for Warren City (420 feet), a complete home well would cost roughly $13,000 to $31,500: $25 to $60 per foot for drilling, casing and seal, plus $2,500 to $6,500 for the pump, pressure tank, controls and hookup at the well. Across the whole middle half of depths (380 to 450 feet) the range runs from $12,000 to $33,500. This is TerraFunded's estimate from published Texas prices, not a quote, and it leaves out trenching and the line to the house. Get prices from at least two licensed drillers.

Where it sits

Nearby places

Median depth of home wells in each place.

All Texas cities and towns

Common questions

How deep do you have to drill a well in Warren City, Texas?

Home water wells in and around Warren City, Texas are typically 380 to 450 feet deep (median 420 ft, 37 wells reported since 2001). One in ten goes past 498 feet. The depth a given tract needs depends on where it sits and what layers the driller hits.

How much does a water well cost in Warren City?

At the median depth (420 feet), a complete well would cost roughly $13,000 to $31,500, by TerraFunded's estimate from published Texas driller prices. The real price comes from a licensed driller's quote.

How deep is the water in Warren City?

When the wells were finished, the water stood a median 180 feet below the surface (29 wells), well above the bottom: the typical well holds about 240 feet of water. The level moves with drought and from one well to the next.

Do I need a permit to drill a well in Warren City?

In the state's boundary file (current as of November 2019) no groundwater conservation district covers Warren City. Districts created or enlarged since then are missing from that file, so confirm with the county or TWDB before drilling. Anywhere in Texas the well must be drilled by a licensed driller, who files the report with the state.

How these numbers are made

We count new and replacement domestic (home) wells whose coordinates fall inside the place boundary or within 2 miles of it. We use the last 10 years when there are at least 30 wells; otherwise all since 2001. The median is the middle well and the middle half runs from the 25th to the 75th percentile.

These are depths of real wells drilled nearby, not a promise about any property. Groundwater can change over short distances and with drought. A licensed water well driller can tell you what to expect on a specific tract.

Read the full methodology · Download the data (CSV, CC BY 4.0)

How to cite

TerraFunded (2026). Texas Well Atlas: Underground. From Texas Water Development Board driller reports and groundwater availability models (data as of November 10, 2026). https://terrafunded.com/wells/places/warren-city-tx. License CC BY 4.0. https://doi.org/10.5281/zenodo.24126380.

Sources