Skip to content
ENES
Marketplace

How deep are water wells in Taylor, Texas?

Home water wells in and around Taylor, Texas are typically 32 to 52 feet deep (median 37 ft, 79 wells reported since 2001). Nearly all are completed in younger formations above the Woodbine (98%), according to the state's Northern Trinity and Woodbine model (TWDB). Estimated cost of a complete well at the median depth: $3,500 to $8,500.

Updated every day from Texas Water Development Board driller reports. Last update: November 11, 2026, using the state file of November 10, 2026.

See the wells and layers at an exact pointWilliamson County
What is under Taylor, TexasUnderground column at the center of Taylor: median well 37 ft, middle half 32 to 52 ft, water at 14 ft, and the layers of the state's model with their thickness.Above the Woodbine: 0 to 936 ftAbove the Woodbinecontinues to 3,759 ft020406080ftGround level · 588 ft above sea levelMedian well: 37 ftWater standing in the well from 14 ftWater level14 ftMiddle half32–52 ftMedian well37 ft

Under Taylor, Williamson County

Layers at the center of Taylor from TWDB's Northern Trinity and Woodbine model (quarter mile cells, summarized here to about 1.3 miles), at true depth scale. The well and the water are the median of 79 real wells.

Home wells in and around Taylor

Each dot is a home well from a state driller report, colored by depth. Tap one for its details and official report. Tap an empty spot to see what is under that point.

See underground

Well depth (ft)

  • <100
  • 100
  • 200
  • 300
  • 400
  • 600
  • 800+

Dashed line: Taylor and about 2 miles around it

Key figures

Typical depth (middle half)
32 to 52 feet
Median depth
37 feet
Deepest 10% are past
71 feet
Water level (median)
14 feet
72 wells
Yield (median)
30 gpm
68 wells, gallons per minute
Wells used
79
Since 2001
Inside the city limits
34
the rest within 2 miles
All years on file
79
median 37 ft, since 2002
Confidence
Standard (30 or more wells)

When the wells were finished, the water stood a median 14 feet below the surface (72 wells), well above the bottom: the typical well holds about 23 feet of water.

What is under Taylor, TexasUnderground column at the center of Taylor: median well 37 ft, middle half 32 to 52 ft, water at 14 ft, and the layers of the state's model with their thickness.Above the Woodbine: 0 to 936 ftAbove the Woodbinecontinues to 3,759 ft020406080ftGround level · 588 ft above sea levelMedian well: 37 ftWater standing in the well from 14 ftWater level14 ftMiddle half32–52 ftMedian well37 ft
Layers at the center of Taylor from TWDB's Northern Trinity and Woodbine model (quarter mile cells, summarized here to about 1.3 miles), at true depth scale. The well and the water are the median of 79 real wells.

Which formation do wells in Taylor draw from?

Nearly all are completed in younger formations above the Woodbine (98%), according to the state's Northern Trinity and Woodbine model (TWDB).

Layer (state's model)ShareWellsTypical depth (ft)
Above the Woodbine98%7732–47
Washita and Fredericksburg3%2—

Only 37% of these wells have the water-bearing interval on their report (reports before about 2012 rarely do). For the others we use the bottom of the hole, which tends to read one layer deeper than where the water actually comes from.

The layers under the center of Taylor

From the state's model, at 588 feet above sea level. These are the model's depths at that one point, not those of any particular lot.

Depths in feet below ground.
Layer (state's model)Top (ft)Bottom (ft)Thickness (ft)
Above the Woodbineshale, chalk and marl0936936
Woodbinesandstone with shale93696630
Washita and Fredericksburglimestone, marl and clay9661,536570
Upper Trinitysandstone, limestone and marl1,5362,403867
Lower Trinitysandstone with shale and limestone2,4033,7591,356

Depth over time

There are not enough wells in both 2003 to 2007 and 2021 to 2025 (at least 30 in each) to say with confidence whether wells in and around Taylor are getting deeper. For reference, the median was 37 feet in 2001 to 2005 (19 wells) and 42 feet in 2021 to 2025 (12 wells).

PeriodMedian depth (ft)Wells
2001–20053719
2006–20105012
2011–20154616
2016–20203420
2021–20254212

What a well costs in Taylor

At the median depth for Taylor (37 feet), a complete home well would cost roughly $3,500 to $8,500: $25 to $60 per foot for drilling, casing and seal, plus $2,500 to $6,500 for the pump, pressure tank, controls and hookup at the well. Across the whole middle half of depths (32 to 52 feet) the range runs from $3,500 to $9,500. This is TerraFunded's estimate from published Texas prices, not a quote, and it leaves out trenching and the line to the house. Get prices from at least two licensed drillers.

Where it sits

Nearby places

Median depth of home wells in each place.

All Texas cities and towns

Common questions

How deep do you have to drill a well in Taylor, Texas?

Home water wells in and around Taylor, Texas are typically 32 to 52 feet deep (median 37 ft, 79 wells reported since 2001). One in ten goes past 71 feet. The depth a given tract needs depends on where it sits and what layers the driller hits.

What aquifer or formation do wells in Taylor draw from?

Nearly all are completed in younger formations above the Woodbine (98%), according to the state's Northern Trinity and Woodbine model (TWDB). This is an estimate from the state's regional model, not a survey of the lot.

How much does a water well cost in Taylor?

At the median depth (37 feet), a complete well would cost roughly $3,500 to $8,500, by TerraFunded's estimate from published Texas driller prices. The real price comes from a licensed driller's quote.

How deep is the water in Taylor?

When the wells were finished, the water stood a median 14 feet below the surface (72 wells), well above the bottom: the typical well holds about 23 feet of water. The level moves with drought and from one well to the next.

Do I need a permit to drill a well in Taylor?

In the state's boundary file (current as of November 2019) no groundwater conservation district covers Taylor. Districts created or enlarged since then are missing from that file, so confirm with the county or TWDB before drilling. Anywhere in Texas the well must be drilled by a licensed driller, who files the report with the state.

How these numbers are made

We count new and replacement domestic (home) wells whose coordinates fall inside the place boundary or within 2 miles of it. We use the last 10 years when there are at least 30 wells; otherwise all since 2001. The median is the middle well and the middle half runs from the 25th to the 75th percentile.

To tell which layer a well draws from, we take the ground elevation at its location, subtract the depth of the interval where water enters (or the bottom of the hole when the report does not give one) and see which layer of the state's model that point falls in.

Only 37% of these wells have the water-bearing interval on their report (reports before about 2012 rarely do). For the others we use the bottom of the hole, which tends to read one layer deeper than where the water actually comes from.

How well it works: In 7,977 wells in the area of the state's Northern Trinity and Woodbine model (North and Central Texas) where the State of Texas recorded the aquifer, our estimate of the formation the well draws from names the same layer of the state's model in about 74% of them, and that layer or the one next to it in at least 95%; among the 3,130 of those wells that the state places in a Trinity layer (Paluxy to Hosston) it is about 56%.

  • The layers come from the Texas Water Development Board's Northern Trinity and Woodbine model, with quarter mile cells, summarized here to about 1.3 miles. It is a regional model, not a survey of any lot: between one model point and the next, the real depth of each layer can differ.
  • In this model every layer is at least 30 feet thick, even where the real rock is thinner or missing. Thin layers and the edges of the model are approximate.
  • Inside the Trinity this atlas does not name single model layers: it groups the Paluxy and Glen Rose (upper Trinity) and groups the Hensell, Pearsall and Hosston (lower Trinity, Twin Mountains and Travis Peak), because the check against the state's codes shows the method cannot separate them reliably.
  • "Near or below the base of the Trinity" means the well reaches the bottom of the model or passes it, often by tens of feet. Older rock that the model does not include may lie there.
  • We never use the model's water levels. The water level on this page is the one each driller measured when the well was finished.

These are depths of real wells drilled nearby, not a promise about any property. Groundwater can change over short distances and with drought. A licensed water well driller can tell you what to expect on a specific tract.

Read the full methodology · Download the data (CSV, CC BY 4.0)

How to cite

TerraFunded (2026). Texas Well Atlas: Underground. From Texas Water Development Board driller reports and groundwater availability models (data as of November 10, 2026). https://terrafunded.com/wells/places/taylor-tx. License CC BY 4.0. https://doi.org/10.5281/zenodo.24126380.

Sources