How deep are water wells in Sulphur Springs, Texas?

Q: How much does a water well cost in Sulphur Springs?

At the median depth (84 feet), a complete well would cost roughly $4,500 to $11,500, by TerraFunded's estimate from published Texas driller prices. The real price comes from a licensed driller's quote.

Q: Do I need a permit to drill a well in Sulphur Springs?

In the state's boundary file (current as of November 2019) no groundwater conservation district covers Sulphur Springs. Districts created or enlarged since then are missing from that file, so confirm with the county or TWDB before drilling. Anywhere in Texas the well must be drilled by a licensed driller, who files the report with the state.

Only 12 home water wells in and around Sulphur Springs, Texas have been reported since 2001, so treat this as a rough guide: the middle half are 83 to 109 feet deep (median 84 ft). Estimated cost of a complete well at the median depth: $4,500 to $11,500.

This page is based on fewer than 30 wells, so it is kept out of search engines until more reports come in. Treat every figure as a rough guide.

Updated every day from Texas Water Development Board driller reports. Last update: November 11, 2026, using the state file of November 10, 2026.

See the wells and layers at an exact point Hopkins County

Under Sulphur Springs, Hopkins County

The well and the water are the median of 12 real wells. This atlas does not have a state layer model for this area yet.

Home wells in and around Sulphur Springs

Each dot is a home well from a state driller report, colored by depth. Tap one for its details and official report. Tap an empty spot to see what is under that point.

See underground

Well depth (ft)

<100
100
200
300
400
600
800+

Dashed line: Sulphur Springs and about 2 miles around it

Key figures

Typical depth (middle half): 83 to 109 feet
Median depth: 84 feet
Deepest 10% are past: 124 feet
Yield (median): 18 gpm; 10 wells, gallons per minute
Wells used: 12; Since 2001
Inside the city limits: 1; the rest within 2 miles
All years on file: 12; median 84 ft, since 2002
Confidence: Few wells (10 to 29)

The well and the water are the median of 12 real wells. This atlas does not have a state layer model for this area yet.

Which formation do wells in Sulphur Springs draw from?

We cannot say yet for Sulphur Springs. This atlas assigns layers with the TWDB layered models processed so far (the Northern Trinity and Woodbine model, the Hill Country Trinity model, the northern Gulf Coast Aquifer model and the High Plains Aquifer System model), and none covers this area with enough wells. The depth, water level and yield on this page do come from the real wells here.

See the aquifers mapped under Hopkins County

Depth over time

Too few wells per period in and around Sulphur Springs to compare depth over time. Since 2002, 12 home wells have been reported, with a median of 84 feet.

Period	Median depth (ft)	Wells
2001–2005	under 10 wells	5
2006–2010	under 10 wells	1
2011–2015	under 10 wells	2
2021–2025	under 10 wells	4

What a well costs in Sulphur Springs

At the median depth for Sulphur Springs (84 feet), a complete home well would cost roughly $4,500 to $11,500: $25 to $60 per foot for drilling, casing and seal, plus $2,500 to $6,500 for the pump, pressure tank, controls and hookup at the well. Across the whole middle half of depths (83 to 109 feet) the range runs from $4,500 to $13,000. This is TerraFunded's estimate from published Texas prices, not a quote, and it leaves out trenching and the line to the house. Get prices from at least two licensed drillers.

Where it sits

Wells in Hopkins County
City · 33.1421, -95.6122

Nearby places

Median depth of home wells in each place.

Como 422 ft
Cumby 734 ft
Yantis 402 ft
Commerce 251 ft
Campbell 274 ft
Emory 222 ft

All Texas cities and towns

Common questions

How deep do you have to drill a well in Sulphur Springs, Texas?

Only 12 home water wells in and around Sulphur Springs, Texas have been reported since 2001, so treat this as a rough guide: the middle half are 83 to 109 feet deep (median 84 ft). One in ten goes past 124 feet. The depth a given tract needs depends on where it sits and what layers the driller hits.

How much does a water well cost in Sulphur Springs?

At the median depth (84 feet), a complete well would cost roughly $4,500 to $11,500, by TerraFunded's estimate from published Texas driller prices. The real price comes from a licensed driller's quote.

Do I need a permit to drill a well in Sulphur Springs?

In the state's boundary file (current as of November 2019) no groundwater conservation district covers Sulphur Springs. Districts created or enlarged since then are missing from that file, so confirm with the county or TWDB before drilling. Anywhere in Texas the well must be drilled by a licensed driller, who files the report with the state.

How these numbers are made

We count new and replacement domestic (home) wells whose coordinates fall inside the place boundary or within 2 miles of it. We use the last 10 years when there are at least 30 wells; otherwise all since 2001. The median is the middle well and the middle half runs from the 25th to the 75th percentile.

These are depths of real wells drilled nearby, not a promise about any property. Groundwater can change over short distances and with drought. A licensed water well driller can tell you what to expect on a specific tract.

Read the full methodology · Download the data (CSV, CC BY 4.0)

How to cite

TerraFunded (2026). Texas Well Atlas: Underground. From Texas Water Development Board driller reports and groundwater availability models (data as of November 10, 2026). https://terrafunded.com/wells/places/sulphur-springs-tx. License CC BY 4.0. https://doi.org/10.5281/zenodo.24126380.