Skip to content
ENES
Marketplace

How deep are water wells in Cut and Shoot, Texas?

Home water wells in and around Cut and Shoot, Texas are typically 170 to 240 feet deep (median 195 ft, 120 wells drilled in the last 10 years). No single layer dominates: 50% draw from the Chicot Aquifer and 50% from the Evangeline Aquifer, according to the state's northern Gulf Coast Aquifer model (TWDB). The split between the Chicot and the Evangeline is approximate. Estimated cost of a complete well at the median depth: $7,500 to $18,000.

Updated every day from Texas Water Development Board driller reports. Last update: November 11, 2026, using the state file of November 10, 2026.

See the wells and layers at an exact pointMontgomery County
What is under Cut and Shoot, TexasUnderground column at the center of Cut and Shoot: median well 195 ft, middle half 170 to 240 ft, water at 51 ft, and the layers of the state's model with their thickness.Chicot: 0 to 190 ftChicotEvangeline: 190 to 490 ftEvangelinecontinues to 3,579 ft0100200300ftGround level · 242 ft above sea levelMedian well: 195 ftWater standing in the well from 51 ftWater level51 ftMiddle half170–240 ftMedian well195 ft

Under Cut and Shoot, Montgomery County

Layers at the center of Cut and Shoot from TWDB's northern Gulf Coast Aquifer model (cells of about 0.62 mile (1 km)), at true depth scale. The well and the water are the median of 120 real wells.

Home wells in and around Cut and Shoot

Each dot is a home well from a state driller report, colored by depth. Tap one for its details and official report. Tap an empty spot to see what is under that point.

See underground

Well depth (ft)

  • <100
  • 100
  • 200
  • 300
  • 400
  • 600
  • 800+

Dashed line: Cut and Shoot and about 2 miles around it

Key figures

Typical depth (middle half)
170 to 240 feet
Median depth
195 feet
Deepest 10% are past
265 feet
Water level (median)
51 feet
117 wells
Yield (median)
35 gpm
111 wells, gallons per minute
Wells used
120
In the last 10 years
Inside the city limits
10
the rest within 2 miles
All years on file
334
median 191 ft, since 1999
Confidence
Standard (30 or more wells)

When the wells were finished, the water stood a median 51 feet below the surface (117 wells), well above the bottom: the typical well holds about 144 feet of water.

What is under Cut and Shoot, TexasUnderground column at the center of Cut and Shoot: median well 195 ft, middle half 170 to 240 ft, water at 51 ft, and the layers of the state's model with their thickness.Chicot: 0 to 190 ftChicotEvangeline: 190 to 490 ftEvangelinecontinues to 3,579 ft0100200300ftGround level · 242 ft above sea levelMedian well: 195 ftWater standing in the well from 51 ftWater level51 ftMiddle half170–240 ftMedian well195 ft
Layers at the center of Cut and Shoot from TWDB's northern Gulf Coast Aquifer model (cells of about 0.62 mile (1 km)), at true depth scale. The well and the water are the median of 120 real wells.

Which formation do wells in Cut and Shoot draw from?

No single layer dominates: 50% draw from the Chicot Aquifer and 50% from the Evangeline Aquifer, according to the state's northern Gulf Coast Aquifer model (TWDB). The line between the Chicot and the Evangeline is drawn differently by different studies, so read that split as approximate: of the wells the state records in the Evangeline, our method finds the Evangeline for only about 51% and the Chicot for most of the rest.

The bottom of the hole tells a different story: 52% reach the Evangeline Aquifer, although only 50% take their water from it. Many drillers go past the producing layer to leave a reserve.

Layer (state's model)ShareWellsTypical depth (ft)
Chicot50%60163–195
Evangeline50%60204–255

For 93% of these wells the report says where the water enters (the screen or the open hole), and we use the middle of that interval.

The layers under the center of Cut and Shoot

From the state's model, at 242 feet above sea level. These are the model's depths at that one point, not those of any particular lot.

Depths in feet below ground.
Layer (state's model)Top (ft)Bottom (ft)Thickness (ft)
Chicotsand, silt and clay0190190
Evangelinesand and clay190490299
Jasper, Catahoula and Burkevillesand, sandstone, clay and volcanic tuff4903,5793,090

Depth over time

Home well depth in and around Cut and Shoot has not changed meaningfully in 20 years: the median was 190 feet in 2003 to 2007 and 184 feet in 2021 to 2025 (a difference under 10% or within the margin of error).

PeriodMedian depth (ft)Wells
2001–200519067
2006–201019575
2011–201518262
2016–202020066
2021–202518459
2026under 10 wells4

What a well costs in Cut and Shoot

At the median depth for Cut and Shoot (195 feet), a complete home well would cost roughly $7,500 to $18,000: $25 to $60 per foot for drilling, casing and seal, plus $2,500 to $6,500 for the pump, pressure tank, controls and hookup at the well. Across the whole middle half of depths (170 to 240 feet) the range runs from $7,000 to $21,000. This is TerraFunded's estimate from published Texas prices, not a quote, and it leaves out trenching and the line to the house. Get prices from at least two licensed drillers.

Where it sits

Nearby places

Median depth of home wells in each place.

All Texas cities and towns

Common questions

How deep do you have to drill a well in Cut and Shoot, Texas?

Home water wells in and around Cut and Shoot, Texas are typically 170 to 240 feet deep (median 195 ft, 120 wells drilled in the last 10 years). One in ten goes past 265 feet. The depth a given tract needs depends on where it sits and what layers the driller hits.

What aquifer or formation do wells in Cut and Shoot draw from?

No single layer dominates: 50% draw from the Chicot Aquifer and 50% from the Evangeline Aquifer, according to the state's northern Gulf Coast Aquifer model (TWDB). The line between the Chicot and the Evangeline is drawn differently by different studies, so read that split as approximate: of the wells the state records in the Evangeline, our method finds the Evangeline for only about 51% and the Chicot for most of the rest. This is an estimate from the state's regional model, not a survey of the lot.

How much does a water well cost in Cut and Shoot?

At the median depth (195 feet), a complete well would cost roughly $7,500 to $18,000, by TerraFunded's estimate from published Texas driller prices. The real price comes from a licensed driller's quote.

How deep is the water in Cut and Shoot?

When the wells were finished, the water stood a median 51 feet below the surface (117 wells), well above the bottom: the typical well holds about 144 feet of water. The level moves with drought and from one well to the next.

Do I need a permit to drill a well in Cut and Shoot?

Cut and Shoot is inside the Lone Star Groundwater Conservation District. Groundwater conservation districts in Texas can require registering or permitting a new well, keeping set distances from property lines and other wells, and paying fees. Rules differ from district to district: ask the district before drilling.

How these numbers are made

We count new and replacement domestic (home) wells whose coordinates fall inside the place boundary or within 2 miles of it. We use the last 10 years when there are at least 30 wells; otherwise all since 2001. The median is the middle well and the middle half runs from the 25th to the 75th percentile.

To tell which layer a well draws from, we take the ground elevation at its location, subtract the depth of the interval where water enters (or the bottom of the hole when the report does not give one) and see which layer of the state's model that point falls in.

For 93% of these wells the report says where the water enters (the screen or the open hole), and we use the middle of that interval.

How well it works: In 14,333 wells in the area of the state's northern Gulf Coast Aquifer model (Houston and Southeast Texas) where the State of Texas recorded the aquifer, the formation our method says the well draws from (as grouped on these pages) is the one the state recorded in about 83% of them, and that formation or the one next to it in at least 99%; of the 3,578 of those wells that the state records in the Evangeline, it names the Evangeline for about 51% and the Chicot for most of the rest.

  • The layers come from the Texas Water Development Board's northern Gulf Coast Aquifer model, with cells of about 0.62 mile (1 km). It is a regional model, not a survey of any lot.
  • The state's model has cells of about 3,277 ft (1 km, 0.62 mile); we read it on a grid of about 0.6 by 0.7 miles. It is not a survey of any lot, so we give ranges.
  • Figures go by three groups: Chicot, Evangeline, and Jasper and Catahoula with the Burkeville. The state's records cannot tell the Burkeville, the Jasper and the Catahoula apart at a well (alone, the Burkeville matched 33% and the Catahoula 50%), so they are never named one by one as the formation of a well or a place.
  • The line between the Chicot and the Evangeline is drawn differently by different studies. The state's records put about half of their Evangeline wells in what the model draws as the Chicot, mostly deeper wells in Harris, Montgomery, Waller, Liberty and Austin counties. Where both appear, the split is approximate.
  • "Near or below the base" means the well ends near or below the base of the Gulf Coast Aquifer (under the Catahoula: Jackson Group, Yegua and older). It is 1.3% of home wells; half of them end within about 85 ft of the base. That is not an error: the model simply ends there.
  • The model's top layer is a uniform 49 ft slab for the water table zone, not a rock unit; we merge it into the unit beneath. The model also covers Colorado, Lavaca, Fayette, Wharton and Matagorda counties (outside Groundwater Management Area 14), with the same framework. Texas part only.
  • We never use the model's water levels. The water level on this page is the one each driller measured when the well was finished.

These are depths of real wells drilled nearby, not a promise about any property. Groundwater can change over short distances and with drought. A licensed water well driller can tell you what to expect on a specific tract.

Read the full methodology · Download the data (CSV, CC BY 4.0)

How to cite

TerraFunded (2026). Texas Well Atlas: Underground. From Texas Water Development Board driller reports and groundwater availability models (data as of November 10, 2026). https://terrafunded.com/wells/places/cut-and-shoot-tx. License CC BY 4.0. https://doi.org/10.5281/zenodo.24126380.

Sources