Skip to content
ENES
Marketplace

How deep are water wells in Ben Bolt, Texas?

Home water wells in and around Ben Bolt, Texas are typically 453 to 658 feet deep (median 520 ft, 91 wells reported since 2001). Estimated cost of a complete well at the median depth: $15,500 to $37,500.

Updated every day from Texas Water Development Board driller reports. Last update: November 11, 2026, using the state file of November 10, 2026.

See the wells and layers at an exact pointJim Wells County
What is under Ben Bolt, TexasUnderground column at the center of Ben Bolt: median well 520 ft, middle half 453 to 658 ft, water at 160 ft.No state layer model here yet0200400600800ftGround levelMedian well: 520 ftWater standing in the well from 160 ftWater level160 ftMiddle half453–658 ftMedian well520 ft

Under Ben Bolt, Jim Wells County

The well and the water are the median of 91 real wells. This atlas does not have a state layer model for this area yet.

Home wells in and around Ben Bolt

Each dot is a home well from a state driller report, colored by depth. Tap one for its details and official report. Tap an empty spot to see what is under that point.

See underground

Well depth (ft)

  • <100
  • 100
  • 200
  • 300
  • 400
  • 600
  • 800+

Dashed line: Ben Bolt and about 2 miles around it

Key figures

Typical depth (middle half)
453 to 658 feet
Median depth
520 feet
Deepest 10% are past
740 feet
Water level (median)
160 feet
85 wells
Yield (median)
30 gpm
84 wells, gallons per minute
Wells used
91
Since 2001
Inside the city limits
30
the rest within 2 miles
All years on file
91
median 520 ft, since 2002
Confidence
Standard (30 or more wells)

When the wells were finished, the water stood a median 160 feet below the surface (85 wells), well above the bottom: the typical well holds about 360 feet of water.

What is under Ben Bolt, TexasUnderground column at the center of Ben Bolt: median well 520 ft, middle half 453 to 658 ft, water at 160 ft.No state layer model here yet0200400600800ftGround levelMedian well: 520 ftWater standing in the well from 160 ftWater level160 ftMiddle half453–658 ftMedian well520 ft
The well and the water are the median of 91 real wells. This atlas does not have a state layer model for this area yet.

Which formation do wells in Ben Bolt draw from?

We cannot say yet for Ben Bolt. This atlas assigns layers with the TWDB layered models processed so far (the Northern Trinity and Woodbine model, the Hill Country Trinity model, the northern Gulf Coast Aquifer model and the High Plains Aquifer System model), and none covers this area with enough wells. The depth, water level and yield on this page do come from the real wells here.

See the aquifers mapped under Jim Wells County

Depth over time

There are not enough wells in both 2003 to 2007 and 2021 to 2025 (at least 30 in each) to say with confidence whether wells in and around Ben Bolt are getting deeper. For reference, the median was 500 feet in 2006 to 2010 (19 wells) and 540 feet in 2016 to 2020 (17 wells).

PeriodMedian depth (ft)Wells
2001–2005under 10 wells7
2006–201050019
2011–201550238
2016–202054017
2021–2025under 10 wells8
2026under 10 wells2

What a well costs in Ben Bolt

At the median depth for Ben Bolt (520 feet), a complete home well would cost roughly $15,500 to $37,500: $25 to $60 per foot for drilling, casing and seal, plus $2,500 to $6,500 for the pump, pressure tank, controls and hookup at the well. Across the whole middle half of depths (453 to 658 feet) the range runs from $14,000 to $46,000. This is TerraFunded's estimate from published Texas prices, not a quote, and it leaves out trenching and the line to the house. Get prices from at least two licensed drillers.

Where it sits

Nearby places

Median depth of home wells in each place.

All Texas cities and towns

Common questions

How deep do you have to drill a well in Ben Bolt, Texas?

Home water wells in and around Ben Bolt, Texas are typically 453 to 658 feet deep (median 520 ft, 91 wells reported since 2001). One in ten goes past 740 feet. The depth a given tract needs depends on where it sits and what layers the driller hits.

How much does a water well cost in Ben Bolt?

At the median depth (520 feet), a complete well would cost roughly $15,500 to $37,500, by TerraFunded's estimate from published Texas driller prices. The real price comes from a licensed driller's quote.

How deep is the water in Ben Bolt?

When the wells were finished, the water stood a median 160 feet below the surface (85 wells), well above the bottom: the typical well holds about 360 feet of water. The level moves with drought and from one well to the next.

Do I need a permit to drill a well in Ben Bolt?

Ben Bolt is inside the Brush Country Groundwater Conservation District. Groundwater conservation districts in Texas can require registering or permitting a new well, keeping set distances from property lines and other wells, and paying fees. Rules differ from district to district: ask the district before drilling.

How these numbers are made

We count new and replacement domestic (home) wells whose coordinates fall inside the place boundary or within 2 miles of it. We use the last 10 years when there are at least 30 wells; otherwise all since 2001. The median is the middle well and the middle half runs from the 25th to the 75th percentile.

These are depths of real wells drilled nearby, not a promise about any property. Groundwater can change over short distances and with drought. A licensed water well driller can tell you what to expect on a specific tract.

Read the full methodology · Download the data (CSV, CC BY 4.0)

How to cite

TerraFunded (2026). Texas Well Atlas: Underground. From Texas Water Development Board driller reports and groundwater availability models (data as of November 10, 2026). https://terrafunded.com/wells/places/ben-bolt-tx. License CC BY 4.0. https://doi.org/10.5281/zenodo.24126380.

Sources